GPO Vehicles


Make Morris
Model J Type
Type 10 cwt Area Radio Investigation Vehicle, type 1 (Morris)
Body Builder  
Use Radio Investigation duties
Registration Number YXF 3
Fleet Number U82518
Date of picture  

Morris J type 10cwt planning van converted for Radio Investigation Duties


P.O. ENGINEERING DEPT.
ENGINEERING INSTRUCTIONS
TOOLS & TRANSPORT
VEHICLES
B 1203
Issue 1, 17.8.64

The 10-cwt. Area Radio Investigation Vehicle, Type 1 (Morris)

1. General
This Instruction describes the l0-cwt. Area Radio Investigation Vehicle, Type 1 (Morris) and the facilities which it provides. The vehicle is designed for use on Area radio investigation duties where the Minor Van, modified for radio investigation work, is inadequate.

2. Description
A general view of the vehicle is shown above. It is a forward-control type with a body shell of welded pressed-sheet-metal construction, having windows along each side. Overall dimensions are: length 12 ft. 9 in., width 5 ft. 8 in. and height 6ft. 9in.

3. Security screen
The cab and body portions are separated by a metal-mesh screen to enable the body to be locked (see par. 9) without restricting access to the cab. This screen incorporates a folding type of access door to give personnel access between cab and body. Provision of hinged traps in the bottom of the screen permits the carriage of a ladder (par. 10). Additionally, the top sections of the screen are removable to give access to the sliding-door pockets (par. 18) for vehicle maintenance purposes.

4. Seating arrangements
In the cab section there is a single passenger seat in addition to that for the driver. Both these seats are adjustable. A further two passengers can be accommodated on a bench seat on the near-side of the body section although this seat is provided for the use of a man operating equipment within the body. The bench seat can be folded back and secured against the side of the vehicle, to give access to underseat lockers (par. 8) and to improve access to equipment carried within the body.

5. Writing facilities
A small writing flap is mounted above the engine cover directly in front of the forward passenger seat. The flap has a sliding support which should always be pulled out when the flap is extended, to avoid straining the hinges. To gain access to the engine the complete table unit can be raised and secured by a strap type of fastener. If necessary the complete unit may be removed by loosening two wing nuts which secure it just below the near-side windscreen.

6. Lockers
An apparatus locker (see right) with three compartments is mounted along the off-side of the body section above the ladder space (par. 10). Access to this locker is obtained via three sliding panels in the top. The two rearmost compartments are lined with shock-absorbent material for the protection of test equipment and can be combined into a single large compartment by withdrawing the removable intervening vertical partition. The remaining compartment is fitted out with two removable trays (displayed on the right) each of which is sub-divided by removable partitions to give adjustable storage for small suppressor components. Space is available below the trays for a tool bag, tool wallets or larger suppressor items.

7. A feature of the sliding panels (one upper and two lower) forming the top of the main locker is that they can be utilized to mount and set out equipment for making tests from within the vehicle, provision being made to secure such equipment in transit by using expanding rubber luggage straps. To make the whole arrangement as flexible as possible, the upper sliding panel may be fixed in one of three alternative positions and each lower panel in one of two positions, using flat slide bolts recessed into the upper faces of the panels. Additionally, the two lower panels can be completely removed via a gap in the sliding channel, to facilitate the removal of the vertical partition separating the two rearmost compartments.

8. There is an underseat locker on the near-side of the body. Access to this locker is obtained by lifting up the near-side bench seat which forms the locker lid. A further small locker under the forward passenger seat accommodates all the vehicle tools except the two long sections of the lifting jack handle which are secured in spring clips on the off-side sliding door pocket.

9. Locking arrangements
The near-side cab door and the rear doors are equipped with standard FA 600 or FP 750 series locks to enable the contents to be safeguarded when the vehicle is left unattended for short periods (the off-side cab door is fitted with an inside turnbutton). For extended absences additional security can be obtained by padlocking the rear doors and the access door between cab and body. A hasp and staple are fitted to the rear doors and the interior door bolt is suitably modified for this purpose. Additionally, the bolts securing traps or removable panels in the security screen are located on the body side. Underseat lockers are equipped with hasp and staple so that they can be padlocked.

Padlocks l.25 in.... are the correct padlocks for use on this class of vehicle. It is advisable to keep all padlocks on the vehicle to one suite.

[NOTE:- Padlocks 1.25 in.... are sometimes of the spring self-locking type. To prevent the accidental locking of keys inside the van body, it is recommended that the padlock keys should not all be carried together.]

10. Ladder carrying facilities
A Ladder, Extension, No. 4A or No. 5 can be carried on the floor in the space below the off-side apparatus locker. The head of the ladder projects through a trap in the bottom of the security screen, into a recess formed below the driverís seat.

11. Aerials
A rotatable aerial-mast housing with coaxial connector box is located towards the rear of the body (Fig. 2). This device is controlled remotely by a handle positioned to the rear of the driverís seat and can be rotated through 400į, care being necessary to ensure that the coaxial cable connecting the connector box and test equipment is long enough to permit this travel. Elongated mounting slots for the remote control handle allow for the adjustment of the remote control wires.

12. Each aerial array (made up locally as required) to be used with the rotatable mast housing requires to be mounted on a 1 in. outside diameter tubular support mast, having two 0.25 in. slots cut diametrically opposite in the bottom end. When the mast is slid into the top of the mast housing, it is turned until these slots locate on to corresponding studs inside the housing above the connector box. The studs have projections outside the housing to form a pointer so that, if the aerial array is lined up with the slots in its support mast, the orientation of the aerial can be followed by an operator inside the vehicle. Connexions to the aerial array are made via a coaxial lead threaded through the support mast and having a short tail with coaxial plug to terminate on a coaxial socket inside the connector box.

13. A business radio aerial (Aerial-units Nos. 17/1 and 17/2) may be fitted centrally on the roof if required. The Workshop Supervisor/Mechanic-in-Charge will fit the aerial base on receipt of a formal request from the Asst. Engr. concerned.

WARNING:- The driver must be extremely careful of low overhead clearances when an aerial array is in position above the roof

14. Power supply for test apparatus
A 5 amp point, mounted above the off-side body window, is wired to the vehicle battery via low resistance leads and is intended for use with test apparatus. Additional power capacity can be obtained by the use of separate 6V car type batteries which should be stowed in a convenient position, using the rubber battery trays supplied with the vehicle. Fig. 2 shows the extra batteries stowed below the operatorís seat.

15. Use of apparatus within the vehicle
While the uses of radio test equipment to be used inside the vehicle are described in the various instructions appertaining to Radio Investigation duties, there are a number of specific precautions to be observed in relation to its use on vehicles. These precautions are:-

(a) Do not drive while wearing earphones

(b) Do not drive holding a microphone or handset

(c) Ensure that legal requirements for the operation of a television set in a vehicle are scrupulously observed. These are:-

  1. No part of the television screen shall be directly or indirectly visible to the driver while he is in the driving seat.

  2. None of the television set controls, other than the main switch and sound volume control, shall be within the driverís reach while he is in the driving seat.

  3. A television set must not be used in circumstances and in a position such that it might cause distraction to the driver of any other vehicle on the road.

16. Maximum load
The maximum load to be carried by this vehicle is 10 cwt. excluding the driver. In cases of doubt a simple check can be made by weighing the vehicle in its moving condition, i.e. complete with contents, personnel, full petrol tank, etc. This gross moving weight must not exceed 40 cwt. Any weighbridge charges involved should be passed to Freight and Cartage.

17. Sliding doors
Under normal driving conditions the cab sliding doors should be kept shut while the vehicle is in motion, as a precaution against accidents. In foggy weather or when manoeuvring in a congested space it may nevertheless be found an advantage to have the doors open. In such circumstances the doors should be secured in the open position by the turn catches near the bottom of each door.

18. Sliding door pockets
The glazed door pocket panels hinge upwards when the securing screws along the bottom edges are freed, to give access for cleaning purposes.

19. First aid kits
The driverís first-aid kit is located above the windscreen. If the personnel regularly using the vehicle are equipped with a larger first-aid kit, this should he mounted in a prominent and accessible position using two leather straps. Two suitable leather straps complete with buckles should be purchased locally where necessary.

20. Windows, lighting and heating
Natural light is provided by the windows in the body and rear doors, the two rear-side windows having sliding panels for ventilation. For night work an internal light is mounted in the body above the near-side windows with the control switch above the off-side door pocket. This general lighting can be augmented by a bench lamp if desired.

21. Blinds
Blinds are provided on the body windows and rear doors. These facilitate the use of a television set within the body and combat difficulties of dazzle from other road users using headlights at night.

22. A cab heater/windscreen demister of the re-circulation type is fitted.

23. Vehicle battery
The vehicle battery is housed beneath the vehicle floor and access is obtained via a floor trap situated immediately behind the driverís seat. A budget lock secures the floor trap.

24. Spare wheel
This is housed at the rear below the floor and, to remove it, the hinged rear number plate should be slid towards the near-side to release a spring-loaded catch, and then raised out of the way.

25. Damage to paintwork
The outside of the van has a synthetic enamel finish. Attempts to re-touch any scratched or damaged parts should not be made by the staff using the vehicle. Work of this nature will be undertaken by the Workshop Supervisor/ Mechanic-in-Charge when necessary and during periodic overhauls.

26. Signwriting
Standard inscriptions for signwriting are given in C 0015.

27. Speed limit
See D 0022

 

BACK Home page BT/GPO Telephones A - Z Index Vehicles Home Page Quick Find All Telephone Systems

Last revised: October 25, 2010

FM