|
|
Mountings, Dial Automatic No. 3 Straight mount Drawing - 7988.
Introduced circa 1919. |
|
|
|
Mountings, Dial Automatic No. 5 Straight mounting that can be used
with a Mountings, Dial Automatic No. 11, to angle the dial.
The Mountings, Dial Automatic No. 5 is shown at the bottom of the picture. |
|
|
|
Mountings, Dial Automatic No. 7 Angled mount, of 14 degrees, used mainly on wall
telephones. Made of mild steel with a Coslettized finish that is stove
enamelled dull black. Drawing - 8586. Introduced circa 1925. |
|
|
|
Mountings, Dial Automatic No. 10 Angled adaptor for converting a
Mountings, Dial No. 5 to sloping top, with an angle of 60
degrees
from the horizontal. |
|
|
|
Mountings, Dial Automatic No. 11 Angled adaptor for converting a
Mountings, Dial No. 5 to sloping top, with an angle of 15
degrees
from the horizontal. |
|
|
|
Mountings, Dial Automatic No. 12 Angled adaptor for converting a
Mountings, Dial No. 5 to sloping top, with an angle of 30
degrees
from the horizontal.
See above
|
|
|
|
Mountings, Dial Automatic No. 15 Sloping top, with an angle of 45
degrees
from the horizontal.
The top of the mounting separates from the mounting plate. |
|
|
|
Mountings, Dial Automatic No. 16 Used with Dials No. 10 and 12.
The actual dial mounting would be normally located in the metal bracket.
The mounting would be pulled out and then dropped down to lock it in the
open position.
Superseded by Mountings, Dial Automatic No. 21 Normally used with a
Bell-set No. 37 and Telephone No.
246. |
|
|
|
Mountings, Dial Automatic No. 17 Switchboards or Teleprinter
switching scheme. Horizontal
Includes:-
1 Part No. 2/SBL/4
1 Part No. 1/SBL/7
To be requisitioned separately as required:-
1 x Cord, Instrument No. 5/19E, 24"
|
|
|
|
Mountings, Dial Automatic No. 18 Straight mount.
The mounting opposite is a PX/1 variant and has a sliding plate for the
dial fixing screw.
The mounting below is a PX/2 variant and has just a hole for the dial
fixing screw. |
|
|
|
Mountings, Dial Automatic No. 20 Dial mounting set at 45 degrees.
|
|
|
|
Mountings, Dial Automatic No. 21 Used with Dials,
Automatic No.
21 or later. The actual dial mounting would be normally located in the
metal bracket. The mounting would be pulled out and then dropped down
to lock it in the open position. Used with Bellset
No. 48 and Telephone No. 713
or Jack Unit No.1. Grey only. |
|
|
|
Mountings, Dial Automatic No. 22A Plastic angled mounting used on
PMBX No. 4.
Angled at 35 degrees from horizontal.
|
|
|
|
Mountings, Dial Automatic No. 23 Angled mount for fixing into
switchboard key board.
The top of the mounting separates from the mounting plate. This is
held in place by lugs which rotate to release the top section.
|
|
|
|
Mountings, Dial Automatic No. 27
Angled mount for fixing into switchboard key board.
The top of the mounting separates from the mounting plate. This is
held in place by the spring clips.
|
|
|
|